Fire Alarm Technician Course

Lesson 1 • Safety Practices in the Field

Covers personal protective equipment, lockout/tagout procedures, and electrical safety rules essential before any hands-on work begins. Establishes a safety-first mindset.

Lesson 2 • Regulatory and Standards Framework

Introduces the governing standards bodies and codes that define installation and maintenance requirements. Students understand why compliance drives every technical decision.

Lesson 3 • Technician Roles and Responsibilities

Outlines the duties of installation, inspection, and service technicians and the distinctions between each role. Connects professional accountability to system reliability.

Lesson 1 • Conductors, Cables, and Conduit

Explains wire gauge, insulation ratings, cable types, and conduit fill rules applicable to fire alarm wiring. Ensures correct material selection during installation.

Lesson 2 • Test Instruments and Measurements

Introduces the multimeter, clamp meter, and loop resistance tester and explains proper measurement techniques. Accurate measurements are prerequisite to all diagnostic work.

Lesson 3 • Reading Electrical Schematics

Teaches interpretation of wiring diagrams, ladder diagrams, and riser diagrams specific to fire alarm systems. Directly supports installation and troubleshooting tasks.

Lesson 4 • Basic Electrical Theory

Covers voltage, current, resistance, and power relationships using Ohm's Law and Watt's Law. Provides the mathematical foundation for all circuit analysis tasks.

Lesson 1 • Auxiliary and Ancillary Devices

Covers relays, door holders, elevator recall modules, and suppression system interfaces. Students recognise how ancillary devices extend system functionality.

Lesson 2 • Initiating Devices: Detectors

Covers smoke, heat, flame, and gas detectors, including their operating principles and placement criteria. Students match detector type to hazard and environment.

Lesson 3 • Notification Appliances

Covers audible and visible notification appliances, including horns, strobes, and combination devices. Students apply candela and decibel requirements to device selection.

Lesson 4 • Initiating Devices: Manual Stations

Explains single-action and dual-action pull stations, their mounting requirements, and accessibility standards. Students understand when and where each type is required.

Lesson 1 • Class A and Class B Circuit Wiring

Explains the fault-tolerance differences between Class A and Class B circuit configurations. Students select the appropriate class based on occupancy and code requirements.

Lesson 2 • Conventional System Architecture

Describes zone-based wiring using initiating device circuits and notification appliance circuits. Students trace conventional circuits and identify zone boundaries.

Lesson 3 • Pathway Survivability Requirements

Introduces pathway survivability levels and the physical protection methods required for each. Students apply survivability requirements to high-rise and critical occupancies.

Lesson 1 • System Labelling and Documentation

Covers circuit labelling, device identification tags, and as-built drawing updates required after installation. Accurate documentation supports future inspection and service.

Lesson 2 • Conductor Termination and Splicing

Explains stripping, crimping, screw-terminal, and push-in termination methods for fire alarm conductors. Proper terminations prevent intermittent faults and failures.

Lesson 3 • Planning and Layout Before Installation

Covers reading construction drawings, coordinating with other trades, and creating a device layout plan. Proper planning prevents costly rework during installation.

Lesson 4 • Device Mounting and Rough-In

Covers back-box installation, device mounting heights, and structural anchoring methods. Correct rough-in ensures devices are accessible and code-compliant.

Lesson 1 • Panel Hardware Familiarisation

Identifies control panel circuit boards, modules, and field wiring terminals for common panel platforms. Students navigate panel hardware before attempting any programming.

Lesson 2 • Monitoring and Communication Setup

Covers programming central station communication paths, including digital communicators and network interfaces. Students verify signal transmission to a monitoring receiver.

Lesson 3 • Commissioning and Acceptance Testing

Guides students through the full commissioning sequence, including 100% device testing and documentation. Acceptance testing confirms the system meets design intent before occupancy.

Lesson 4 • Input and Output Mapping

Explains how to map initiating device inputs to notification appliance outputs and ancillary control relays. Correct mapping ensures the right devices activate for each alarm condition.

Lesson 1 • Detector Testing Procedures

Covers functional testing of smoke, heat, and flame detectors using approved test methods and equipment. Students select the correct test method for each detector technology.

Lesson 2 • Inspection and Testing Standards Overview

Introduces the required frequencies and methods for inspection and testing defined by governing standards. Students understand the legal and liability basis for scheduled testing.

Lesson 3 • Completing Inspection Reports

Teaches how to complete standardised inspection forms, record deficiencies, and communicate findings to building owners. Proper reporting protects the technician and the client.

Lesson 4 • Notification Appliance Testing

Explains how to verify audible output levels and strobe flash rates against design specifications. Students use sound level meters and photometric tools during testing.

Lesson 1 • Nuisance Alarm Investigation

Identifies environmental, mechanical, and programming causes of unwanted alarms and corrective actions. Reducing nuisance alarms improves occupant trust and system credibility.

Lesson 2 • Diagnosing Initiating Device Faults

Explains how to isolate faulty detectors, manual stations, and modules using loop isolation and substitution. Students distinguish device failure from wiring faults.

Lesson 3 • Diagnosing Notification Appliance Faults

Covers open circuit, short circuit, and ground fault diagnosis on notification appliance circuits. Students restore circuit integrity and verify corrected appliance operation.

Lesson 4 • Troubleshooting Methodology

Introduces a structured fault-isolation process using symptom analysis, hypothesis testing, and verification. A repeatable method reduces diagnostic time and prevents misdiagnosis.