CCTV and Alarm Installation Course

Lesson 1 • Electrical Safety Essentials

Teaches safe handling of low-voltage and line-voltage circuits encountered during installations. Prevents electrical injury throughout all wiring and installation chapters.

Lesson 2 • Workplace Safety and PPE

Introduces hazard identification, personal protective equipment selection, and safe work practices. Directly supports safe execution of all hands-on lab activities.

Lesson 3 • Security Industry Roles and Scope

Covers the structure of the alarm and video surveillance industry, key stakeholders, and technician career paths. Provides context for all subsequent technical training.

Lesson 1 • Test Instruments and Measurements

Teaches use of multimeters, cable testers, and tone generators for circuit verification. Directly supports fault isolation in all subsequent installation and troubleshooting chapters.

Lesson 2 • Cables, Conductors, and Connectors

Identifies cable types, conductor gauges, and connector standards used in security installations. Enables correct material selection for alarm and video runs.

Lesson 3 • DC Circuit Theory

Covers voltage, current, resistance, and Ohm's Law as applied to low-voltage security circuits. Forms the mathematical foundation for all wiring and troubleshooting tasks.

Lesson 4 • AC Power and Transformers

Explains alternating current principles and transformer operation used in panel power supplies. Prepares students to safely connect and verify AC power sources.

Lesson 1 • Alarm Communication Pathways

Surveys PSTN, cellular, IP, and dual-path communication methods for alarm signal transmission. Prepares students to select and configure appropriate communication modules.

Lesson 2 • Control Panels and Power Supplies

Examines alarm control panel architecture, zone inputs, output relays, and backup power. Establishes the central hub concept before peripheral devices are introduced.

Lesson 3 • Detection Devices and Sensors

Covers magnetic contacts, motion detectors, glass-break sensors, and environmental detectors. Students match sensor technology to specific threat and environmental conditions.

Lesson 4 • System Zones and Loop Configurations

Details hardwired zone loop types including normally open, normally closed, and end-of-line resistor configurations. Enables correct wiring and supervision of detection circuits.

Lesson 1 • Site Survey and Installation Planning

Teaches pre-installation site assessment, sensor placement strategy, and cable routing planning. Prevents costly rework by establishing good planning habits before any drilling begins.

Lesson 2 • Customer Handover and User Training

Teaches system demonstration, user code setup, and documentation delivery to end users. Completes the installation workflow and establishes professional service standards.

Lesson 3 • System Commissioning and Walk-Test

Covers powering up, initial diagnostics, and walk-testing every zone for proper operation. Ensures students can verify a complete, functional installation before handoff.

Lesson 4 • Panel Wiring and Terminations

Guides students through zone wiring, power connections, and communicator hookup at the control panel. Directly applies electrical fundamentals to a real alarm installation.

Lesson 1 • Camera Form Factors and Housing

Surveys bullet, dome, PTZ, fisheye, and covert camera types and their environmental ratings. Matches camera form factor to installation environment and surveillance objective.

Lesson 2 • Lighting and Image Quality Factors

Addresses illumination levels, IR lighting, backlight compensation, and WDR for reliable imaging. Directly impacts camera placement and specification decisions in later chapters.

Lesson 3 • Analog vs. IP Video Systems

Compares analog CCTV, HD-over-coax, and IP network camera architectures. Prepares students to work with both legacy and modern video infrastructure.

Lesson 4 • Lens Selection and Field of View

Covers focal length, aperture, depth of field, and lens format for surveillance applications. Enables accurate field-of-view calculations during site design.

Lesson 1 • IP Camera Configuration and Verification

Covers IP address assignment, camera web interface setup, and live image verification. Completes the installation workflow before NVR and recording configuration.

Lesson 2 • Camera Placement and Site Design

Applies field-of-view calculations, coverage mapping, and lighting analysis to camera layout design. Translates surveillance objectives into a documented camera placement plan.

Lesson 3 • IP Camera Network Infrastructure

Teaches structured cabling, PoE switch configuration, and VLAN segmentation for IP camera networks. Establishes the network foundation required for NVR and VMS configuration.

Lesson 4 • Camera Mounting and Alignment

Guides physical mounting of cameras on walls, ceilings, poles, and junction boxes with proper alignment. Ensures correct field of view and mechanical security after installation.

Lesson 1 • DVR and NVR Platform Overview

Compares DVR and NVR hardware architectures, channel capacities, and supported camera types. Provides the platform context needed for configuration and storage planning.

Lesson 2 • Footage Retrieval and Export

Teaches timeline-based playback, clip export, and chain-of-custody documentation for evidentiary use. Completes the recording workflow from capture through legal handover.

Lesson 3 • Recording Schedules and Triggers

Configures continuous, scheduled, and event-triggered recording modes including motion and alarm inputs. Optimises storage use whilst meeting evidence and compliance requirements.

Lesson 4 • Video Management Software Configuration

Covers VMS installation, camera onboarding, user permissions, and live monitoring layout setup. Prepares students to deploy enterprise-grade video management platforms.

Lesson 1 • Video System Fault Diagnosis

Addresses no-image, poor-image, and network connectivity faults in analogue and IP camera systems. Builds diagnostic confidence across both legacy and modern video platforms.

Lesson 2 • Alarm System Fault Diagnosis

Covers panel trouble codes, zone fault analysis, communication failures, and power supply issues. Applies the troubleshooting methodology to real alarm system scenarios.

Lesson 3 • Service Documentation and Reporting

Teaches work order completion, service report writing, and as-built drawing updates after service calls. Ensures accurate records for warranty, compliance, and future technicians.

Lesson 4 • Preventive Maintenance Procedures

Establishes scheduled maintenance tasks for sensors, cameras, panels, and batteries. Reduces system downtime and extends equipment life through proactive service.