Cabinet & Furniture Installation Training

Lesson 1 • Hardware Identification and Selection

Surveys hinges, drawer slides, pulls, and specialty hardware used in cabinet installation. Correct hardware selection ensures smooth operation and long-term durability.

Lesson 2 • Cabinet Types and Construction Methods

Covers framed, frameless, and inset cabinet construction differences. Establishes the vocabulary needed for all subsequent installation decisions.

Lesson 3 • Reading Installation Drawings

Teaches interpretation of elevation drawings, floor plans, and shop drawings. Accurate drawing reading prevents costly layout errors throughout the project.

Lesson 4 • Jobsite Safety Fundamentals

Establishes personal protective equipment use, hazard identification, and safe lifting practices. Safety compliance protects workers and reduces project liability.

Lesson 1 • Evaluating Existing Site Conditions

Covers inspection of walls, floors, and ceilings for plumb, level, and square. Identifying defects early prevents rework and structural conflicts during installation.

Lesson 2 • Sequencing the Installation Plan

Establishes the optimal order for installing base, upper, and tall cabinets. A logical sequence minimises handling conflicts and protects finished surfaces.

Lesson 3 • Locating Utilities and Obstructions

Identifies plumbing, electrical, and HVAC elements that affect cabinet placement. Utility conflicts resolved at the planning stage prevent costly field modifications.

Lesson 1 • Scribing and Fitting to Walls

Covers scribing techniques for fitting cabinets flush against irregular wall surfaces. Tight scribes eliminate gaps that compromise both aesthetics and structural support.

Lesson 2 • Toe Kick Installation and Finishing

Teaches cutting, fitting, and attaching toe kick material to complete the base cabinet run. Properly fitted toe kicks protect the cabinet base and deliver a finished look.

Lesson 3 • Joining and Aligning Adjacent Cabinets

Teaches clamping, face-frame alignment, and cabinet-to-cabinet fastening techniques. Tight, flush joints between cabinets produce a professional finished appearance.

Lesson 4 • Setting the First Base Cabinet

Covers selecting the starting cabinet, shimming to the reference line, and initial fastening. The first cabinet establishes alignment for every subsequent unit in the run.

Lesson 1 • Lifting and Positioning Upper Cabinets

Teaches safe lifting methods, cabinet jacks, and two-person positioning techniques. Controlled positioning prevents wall damage and installer injury during hanging.

Lesson 2 • Crown Moulding and Top Trim

Teaches measuring, cutting, and attaching crown moulding to finish the upper cabinet run. Crown moulding conceals gaps and elevates the overall visual quality of the installation.

Lesson 3 • Fastening Upper Cabinets to Walls

Covers screw selection, fastening into studs, and using wall anchors where studs are absent. Correct fastening ensures cabinets support the rated load without failure.

Lesson 4 • Aligning and Joining Upper Cabinet Runs

Addresses face-frame alignment, shimming at the wall, and joining adjacent upper units. Consistent alignment across the run creates a seamless, professional installation.

Lesson 1 • Oven and Appliance Tower Installation

Addresses cutout sizing, appliance clearances, and structural support for built-in oven towers. Correct clearances ensure appliance function and meet manufacturer requirements.

Lesson 2 • Refrigerator and Built-In Surround Panels

Covers building and attaching surround panels, filler strips, and gable ends around refrigerators. Integrated surrounds create a built-in appearance and protect adjacent cabinets.

Lesson 3 • Tall Cabinet Structural Requirements

Covers load calculations, anti-tip anchoring, and wall blocking for tall units. Structural compliance prevents tip-over hazards and satisfies safety standards.

Lesson 1 • Drawer Slide Installation

Covers side-mount, undermount, and centre-mount slide installation and alignment. Properly installed slides ensure smooth, rattle-free drawer operation under load.

Lesson 2 • Pull and Knob Installation

Covers jig-based layout, drilling, and mounting of pulls and knobs on doors and drawers. Consistent hardware placement reinforces the visual precision of the finished installation.

Lesson 3 • Hinge Installation and Door Hanging

Covers cup hinge boring, mounting plate placement, and initial door hanging. Accurate hinge placement is the foundation for all subsequent door adjustments.

Lesson 4 • Six-Way Door Adjustment Techniques

Teaches up-down, left-right, and in-out hinge adjustments to achieve uniform reveals. Mastery of six-way adjustment eliminates rework and produces a polished result.

Lesson 1 • Cutting and Fitting Laminate Countertops

Covers scribing, cutting, and fitting post-form and custom laminate countertops. Accurate cuts and tight scribes produce a professional, gap-free installation.

Lesson 2 • Securing and Sealing Countertops

Teaches fastening methods, silicone sealing, and caulking for all countertop materials. Proper sealing prevents water infiltration and protects cabinet boxes below.

Lesson 3 • Sink and Cooktop Cutout Completion

Covers drop-in, undermount, and farmhouse sink installation within the countertop. Correct cutout sizing and clip placement ensure a watertight, stable sink fit.

Lesson 4 • Countertop Material Properties

Surveys laminate, solid surface, quartz, and natural stone material characteristics. Understanding material behaviour guides correct cutting, support, and sealing decisions.

Lesson 1 • Systematic Installation Inspection

Teaches a structured walk-through process to identify alignment, fastening, and finish defects. Catching defects before client review prevents costly callbacks and reputation damage.

Lesson 2 • Touch-Up and Surface Finishing

Teaches filling screw holes, touching up paint, and applying final caulk beads. Surface finishing transforms a functional installation into a polished, sellable product.

Lesson 3 • Client Walkthrough and Handover

Covers demonstrating hardware operation, explaining care instructions, and obtaining sign-off. A professional handover builds client confidence and reduces post-installation service calls.

Lesson 4 • Punch-List Creation and Resolution

Covers documenting deficiencies, prioritising repairs, and tracking completion status. A thorough punch list ensures no defect is overlooked before project sign-off.