Kitchen Installation Course

Lesson 1 • Workplace Safety Fundamentals

Establishes mandatory safety protocols for cutting, lifting, and working near utilities. Safe habits prevent injury throughout all subsequent practical chapters.

Lesson 2 • The Kitchen Installation Trade

Covers the scope of kitchen installation work, career pathways, and industry standards. Establishes professional context before any hands-on skill is introduced.

Lesson 3 • Tools and Equipment Essentials

Identifies hand tools, power tools, and measuring instruments used in kitchen installation. Correct tool selection underpins every technique taught later.

Lesson 1 • Reading Architectural Plans

Teaches interpretation of floor plans, elevations, and detail drawings for kitchens. Plan-reading skills directly inform every measurement and layout decision.

Lesson 2 • Conducting a Site Survey

Covers systematic room measurement, wall plumb checks, and floor level assessment. Survey data becomes the foundation for accurate cabinet ordering and layout.

Lesson 3 • Identifying Common Site Defects

Trains recognition of out-of-level floors, bowed walls, and structural obstructions. Early defect identification allows corrective action before installation starts.

Lesson 1 • Cabinet Run Planning and Sequencing

Covers how to plan cabinet runs, establish reference lines, and sequence installation order. Proper sequencing prevents rework and ensures alignment across the entire kitchen.

Lesson 2 • Common Kitchen Layout Configurations

Examines galley, L-shape, U-shape, island, and peninsula layouts with their trade-offs. Configuration knowledge enables informed recommendations to clients and designers.

Lesson 3 • Ergonomics and Work Triangle Principles

Introduces the work triangle concept and ergonomic height standards for kitchens. These principles guide every layout decision made in subsequent sections.

Lesson 1 • Preparing the Installation Area

Covers substrate preparation, utility protection, and marking reference lines on walls and floors. Thorough preparation is the single biggest factor in a level, aligned installation.

Lesson 2 • Setting and Leveling Base Cabinets

Teaches shimming, leg-leveling, and scribing techniques to achieve a level base run. Levelling accuracy at this stage determines countertop fit and appliance alignment.

Lesson 3 • Quality Checking the Base Run

Establishes inspection criteria for level, plumb, square, and gap tolerances across the completed base run. Systematic checks catch errors before wall cabinets and countertops are installed.

Lesson 4 • Fastening and Joining Base Cabinets

Covers face-frame and frameless joining methods, fastener selection, and wall anchoring. Secure fastening ensures structural integrity and long-term cabinet performance.

Lesson 1 • Safe Overhead Installation Techniques

Covers cabinet jacks, temporary ledger boards, and two-person lift procedures for wall cabinets. Safe overhead methods prevent injury and cabinet damage during hanging.

Lesson 2 • Fastening Wall Cabinets to Structure

Details anchor bolt selection, toggle bolt use in hollow walls, and rail-hanging systems. Correct fastening prevents cabinet failure under load from dishes and appliances.

Lesson 3 • Wall Cabinet Layout and Reference Lines

Establishes upper datum lines and stud locations to guide wall cabinet positioning. Accurate reference lines ensure consistent reveal and alignment with base cabinets below.

Lesson 4 • Aligning and Adjusting the Full Cabinet Suite

Teaches final alignment of doors, hinges, and reveals across the complete cabinet installation. A unified, aligned suite is the hallmark of professional-quality work.

Lesson 1 • Cutting and Fabricating Laminate Countertops

Teaches on-site cutting, edge-banding, and post-forming of laminate countertops. Laminate fabrication skills allow installers to handle adjustments without outsourcing.

Lesson 2 • Templating and Measuring for Countertops

Covers cardboard and digital templating methods to capture exact countertop profiles. Accurate templates are critical for stone and solid-surface materials cut off-site.

Lesson 3 • Countertop Materials and Selection

Compares laminate, solid surface, engineered stone, natural stone, and timber countertops. Material properties determine fabrication methods and installation requirements covered next.

Lesson 4 • Sealing, Finishing, and Waterproofing

Applies sealants at wall junctions, sink cutouts, and seams to prevent water ingress. Proper sealing protects substrate integrity and meets hygiene standards.

Lesson 1 • Dishwasher and Refrigerator Integration

Teaches dishwasher panel fitting, leveling, and anti-tip anchoring alongside refrigerator surround installation. Integrated appliances require precise panel alignment for a seamless look.

Lesson 2 • Cooktop and Range Hood Fitting

Addresses gas and electric cooktop cutouts, sealing, and range hood ducting connections. Appliance fitting must respect manufacturer clearances and ventilation requirements.

Lesson 3 • Sink and Faucet Installation

Covers undermount, top-mount, and integrated sink fitting with faucet and waste connections. Correct sink installation prevents leaks and ensures drainage compliance.

Lesson 1 • Conducting a Snag Inspection

Establishes a structured snag checklist covering alignment, gaps, operation, and finish quality. Systematic snagging ensures every defect is found and resolved before handover.

Lesson 2 • Client Walkthrough and Handover

Guides the installer through a professional client walkthrough, demonstrating features and collecting sign-off. A structured handover builds client confidence and protects the installer.

Lesson 3 • Scribing, Fillers, and Trim Work

Teaches scribing panels to walls, fitting filler strips, and installing plinths and cornice moldings. Trim work conceals gaps and gives the kitchen a built-in, finished appearance.

Lesson 4 • Installing Hardware and Accessories

Covers handle fitting, soft-close hinge adjustment, drawer runner tuning, and interior fittings. Hardware installation is the final functional step before snagging begins.