Electrician Course for Beginners

Lesson 1 • Regulatory Standards and Codes

Introduces the national electrical safety standards and inspection frameworks governing all installation work. Students understand compliance obligations before touching any wiring.

Lesson 2 • Personal Protective Equipment

Identifies required PPE for electrical work and correct usage procedures. Links proper gear selection to specific voltage levels and task types.

Lesson 3 • Lockout and Tagout Procedures

Teaches the step-by-step process for de-energising equipment before work begins. Directly prevents accidental energisation, the leading cause of electrical fatalities.

Lesson 1 • Alternating Current Fundamentals

Introduces AC waveforms, frequency, and phase relationships used in utility power systems. Prepares students for the AC-dominant environments found in all residential and commercial work.

Lesson 2 • Atomic Structure and Electron Flow

Explains how atomic structure drives electron movement and creates electrical current. Provides the physical basis for all circuit behaviour studied in later sections.

Lesson 3 • Series and Parallel Circuits

Analyses how components behave differently in series versus parallel configurations. Builds the analytical skills needed for reading and designing residential wiring layouts.

Lesson 4 • Ohm's Law and Power Formulas

Applies Ohm's Law and the power equation to calculate unknown circuit values. Students solve practical problems that mirror real installation and troubleshooting scenarios.

Lesson 1 • Clamp Meters and Specialty Testers

Covers clamp meters for non-contact current measurement and specialty testers for outlets and circuits. Students choose the right instrument for each diagnostic task.

Lesson 2 • Power Tools for Electrical Work

Introduces drills, hole saws, reciprocating saws, and conduit benders used in rough-in work. Safe operation techniques are paired with each tool's specific electrical application.

Lesson 3 • Using a Multimeter

Teaches voltage, resistance, and continuity measurements using a digital multimeter. This instrument is the most frequently used diagnostic tool throughout an electrician's career.

Lesson 1 • Conductors and Wire Types

Explains wire gauge systems, insulation types, and ampacity ratings for copper and aluminium conductors. Correct conductor selection prevents overheating and code violations.

Lesson 2 • Switches, Receptacles, and Devices

Covers single-pole, three-way, and GFCI/AFCI devices along with their wiring configurations. Students understand device ratings and placement rules for residential circuits.

Lesson 3 • Cable Assemblies and Raceways

Covers NM cable, armoured cable, and conduit types used to route and protect conductors. Students match the wiring method to the environment and occupancy type.

Lesson 4 • Overcurrent Protection Devices

Explains fuses and circuit breakers, their ratings, and how they protect conductors from overcurrent. Students select the correct device size for each circuit application.

Lesson 1 • Blueprint Basics and Symbols

Introduces drawing scales, title blocks, and standard electrical symbols found on construction documents. Symbol literacy is the entry point for all plan-reading tasks.

Lesson 2 • One-Line and Riser Diagrams

Covers one-line diagrams for power distribution and riser diagrams for multi-floor systems. Students extract panel sizing and feeder routing information from these documents.

Lesson 3 • Residential Electrical Floor Plans

Teaches how to locate outlets, switches, fixtures, and panel schedules on residential floor plans. Students count devices and plan rough-in layouts from the drawings.

Lesson 1 • Load Calculations for Panels

Applies the standard method for calculating residential electrical loads to size service panels. Students determine whether an existing or new panel meets the home's demand.

Lesson 2 • Installing Circuit Breakers

Teaches how to install single-pole and double-pole breakers and land conductors on the bus. Students follow torque specifications and conductor preparation procedures.

Lesson 3 • Service Entrance Components

Identifies the meter base, service entrance conductors, weatherhead, and main disconnect. Students trace the path of utility power from the pole to the panel.

Lesson 1 • 240-Volt Appliance Circuits

Covers wiring dryers, ranges, water heaters, and HVAC units on 240 V circuits. Students size conductors and breakers and make correct four-wire appliance connections.

Lesson 2 • Kitchen and Bathroom Circuits

Addresses the dedicated and GFCI-protected circuits required in kitchens, bathrooms, and wet areas. Students apply heightened code requirements for these high-use spaces.

Lesson 3 • Wiring General-Purpose Circuits

Teaches wiring 15 A and 20 A branch circuits for lighting and receptacles in living areas. Students apply device spacing rules and circuit load limits from the electrical code.

Lesson 4 • Rough-In Wiring Procedures

Covers box placement, cable routing, stapling, and drilling for the rough-in phase of construction. Correct rough-in work ensures smooth inspections and finish wiring.

Lesson 1 • Testing for Opens and Shorts

Covers continuity and resistance testing to locate open conductors and short circuits. Students use multimeters to pinpoint faults without unnecessary disassembly.

Lesson 2 • Repairing and Verifying Repairs

Covers splice repair, device replacement, and post-repair testing to confirm circuit integrity. Students verify that repairs meet code before restoring power to the circuit.

Lesson 3 • Earth Fault Diagnosis

Teaches how to detect and locate earth faults that trip GFCI devices or breakers. Students distinguish earth faults from short circuits and apply targeted repairs.

Lesson 4 • Voltage Drop and Load Problems

Diagnoses circuits with excessive voltage drop, overloaded conductors, and undersized breakers. Students calculate acceptable drop limits and recommend corrective actions.