Power Distribution Electrician Course

Lesson 1 • Series and Parallel Circuit Analysis

Teaches circuit topology and load behaviour in series and parallel configurations. Directly supports fault analysis and load balancing tasks in distribution systems.

Lesson 2 • Magnetism and Electromagnetic Induction

Explains magnetic fields, flux, and Faraday's Law as the basis for transformer and motor operation. Prepares students for transformer theory in later chapters.

Lesson 3 • Three-Phase Power Systems

Introduces balanced and unbalanced three-phase systems, phasor diagrams, and power calculations. Forms the core mathematical framework for distribution network analysis.

Lesson 1 • Overhead Line Hardware and Conductors

Covers conductor types, insulator classes, crossarms, and hardware used on overhead lines. Provides the component knowledge required for line construction and inspection.

Lesson 2 • Underground Cable Systems

Describes cable construction, insulation classes, and duct bank arrangements for underground distribution. Connects to installation and fault-location procedures covered later.

Lesson 3 • Distribution Transformers

Explains single-phase and three-phase distribution transformer construction, ratings, and connections. Builds the equipment knowledge needed for transformer installation and testing.

Lesson 4 • Switching and Protection Devices

Covers fuses, reclosers, sectionalizers, and switches used to protect and isolate distribution circuits. Prepares students for switching procedures and protection coordination.

Lesson 1 • Approach Boundaries and Minimum Distances

Defines limited, restricted, and prohibited approach boundaries for qualified workers at distribution voltages. Ensures compliance with approach distance requirements during all field operations.

Lesson 2 • Personal Protective Equipment

Covers selection, inspection, and use of rubber insulating gloves, sleeves, blankets, and arc-rated clothing. Directly reduces injury risk during all hands-on distribution tasks.

Lesson 3 • Lockout/Tagout and Grounding Procedures

Teaches energy isolation, verification, and protective earthing for de-energised distribution equipment. Prevents accidental re-energisation during maintenance and construction work.

Lesson 4 • Electrical Hazard Recognition

Identifies shock, arc flash, and induced voltage hazards specific to distribution environments. Establishes hazard awareness as the foundation for all safe work procedures.

Lesson 1 • Conductor Stringing and Sagging

Teaches tensioned and slack stringing methods, sag tables, and clipping procedures for distribution conductors. Ensures correct mechanical tension and clearance on completed lines.

Lesson 2 • Transformer and Equipment Installation

Covers pole-top and pad-mount transformer installation, earthing, and secondary connections. Builds practical skills for energising new distribution transformer installations.

Lesson 3 • Overhead Line Maintenance and Inspection

Describes patrol inspection methods, defect classification, and corrective maintenance for overhead lines. Supports asset reliability and regulatory compliance for distribution infrastructure.

Lesson 4 • Pole Setting and Framing

Covers wood and concrete pole classification, setting depth calculations, and crossarm framing configurations. Provides the structural foundation for all overhead line construction tasks.

Lesson 1 • Pad-Mount Equipment Installation

Describes installation, earthing, and connection of pad-mount transformers and switchgear. Integrates underground cable skills with equipment commissioning procedures.

Lesson 2 • Cable Pulling and Installation

Teaches cable pulling tension limits, lubricant selection, and reel handling for underground distribution cables. Prevents cable damage that leads to premature insulation failure.

Lesson 3 • Trenching, Conduit, and Duct Bank Installation

Covers excavation safety, conduit types, duct bank construction, and backfill requirements for underground systems. Establishes the civil infrastructure skills needed before cable installation.

Lesson 4 • Cable Splicing and Termination

Covers heat-shrink, cold-shrink, and pre-moulded splice and termination techniques for medium-voltage cables. Ensures watertight, electrically sound connections at every cable joint.

Lesson 1 • Recloser and Sectionaliser Coordination

Teaches multi-shot recloser sequences, sectionaliser count settings, and coordination with downstream fuses. Reduces permanent outages by isolating only the faulted section of a feeder.

Lesson 2 • Voltage and Capacitor Bank Protection

Covers overvoltage, undervoltage, and capacitor bank protection schemes on distribution feeders. Maintains voltage quality and prevents capacitor failures that cause widespread outages.

Lesson 3 • Fault Types and Fault Current Analysis

Explains three-phase, line-to-line, and earth fault types and their current magnitudes on distribution systems. Provides the analytical basis for selecting and setting protective devices.

Lesson 4 • Earth Fault Protection

Addresses zero-sequence current detection, neutral earthing methods, and earth fault relay settings. Protects personnel and equipment from sustained earth faults on distribution feeders.

Lesson 1 • Post-Fault Analysis and Reporting

Covers root cause analysis, outage reporting, and corrective action documentation after distribution faults. Drives continuous improvement in network reliability and maintenance planning.

Lesson 2 • Overhead Fault Investigation

Teaches systematic patrol, visual inspection, and test procedures for locating faults on overhead feeders. Builds on overhead construction knowledge to speed fault identification.

Lesson 3 • Switching for System Restoration

Describes manual and automated switching sequences to restore unfaulted sections whilst isolating faults. Integrates protection knowledge with network topology to minimise outage scope.

Lesson 4 • Fault Location Principles and Methods

Covers impedance-based, time-domain reflectometry, and sectionalising methods for locating distribution faults. Provides the diagnostic framework applied in all subsequent fault-location sections.

Lesson 1 • Capacitor Banks for Voltage Support

Explains fixed and switched capacitor bank sizing, placement, and control for reactive power compensation. Reduces line losses and improves voltage at the end of long feeders.

Lesson 2 • Voltage Drop and Feeder Voltage Profiles

Calculates voltage drop along distribution feeders using impedance and load data. Establishes the analytical baseline for selecting and placing voltage regulation equipment.

Lesson 3 • Power Quality Disturbances

Identifies harmonics, voltage sags, swells, flicker, and transients affecting distribution customers. Provides the diagnostic vocabulary and measurement approach for power quality investigations.

Lesson 4 • Power Quality Mitigation Strategies

Covers harmonic filters, surge protective devices, and network reconfiguration to resolve power quality issues. Completes the voltage and power quality competency arc of this chapter.