Driller Training Course

Lesson 1 • Rig Crew Roles and Responsibilities

Defines the chain of command from company man to floorhand and each role's duties. Clarifies the driller's authority and accountability within the crew structure.

Lesson 2 • The Drilling Industry Overview

Covers the purpose of drilling in oil, gas, and geothermal sectors and the economic drivers behind it. Establishes context for all technical content that follows.

Lesson 3 • Regulatory and Compliance Framework

Introduces the regulatory bodies, permit requirements, and operator obligations governing drilling. Prepares drillers to operate within compliance boundaries from day one.

Lesson 4 • Rig Types and Configurations

Examines land rigs, jackups, semi-submersibles, and drillships by design and application. Connects rig selection to well objectives and environmental conditions.

Lesson 1 • Emergency Response and Evacuation

Trains drillers to lead muster, evacuation, and rescue operations during rig emergencies. Integrates with the crew roles established in Chapter 1.

Lesson 2 • Safety Culture and Personal Responsibility

Establishes the behaviors, attitudes, and leadership practices that define a strong safety culture. Connects individual accountability to overall rig safety performance.

Lesson 3 • Fire, Explosion, and H2S Hazards

Addresses ignition sources, flammable atmospheres, and hydrogen sulfide detection and response. Equips drillers to initiate emergency actions when these hazards are present.

Lesson 4 • Hazard Identification and Risk Assessment

Teaches job hazard analysis, risk matrices, and pre-task planning tools used before each operation. Directly supports the driller's duty to assess conditions before authorizing work.

Lesson 1 • Fluid Properties and Testing

Covers density, viscosity, filtration, and pH testing methods performed at the rig site. Enables drillers to interpret mud reports and direct corrective treatments.

Lesson 2 • Drilling Fluid Functions and Types

Explains how drilling fluids control pressure, cool the bit, and transport cuttings. Differentiates water-based, oil-based, and synthetic fluid systems by application.

Lesson 3 • Solids Control and Waste Management

Describes shale shakers, desanders, desilters, and centrifuges used to maintain fluid quality. Addresses environmental disposal requirements for drill cuttings and waste fluids.

Lesson 4 • Fluid Additives and Treatments

Identifies weighting agents, viscosifiers, filtration reducers, and lost-circulation materials. Connects additive selection to specific downhole problems encountered during drilling.

Lesson 1 • Torque, Drag, and String Mechanics

Applies torque-and-drag modeling concepts to predict and manage friction in the wellbore. Enables drillers to distinguish normal friction from stuck-pipe indicators.

Lesson 2 • Drill String Components

Identifies drill pipe, heavy-weight drill pipe, drill collars, and specialty subs by function. Establishes the mechanical foundation for weight-on-bit and torque transmission.

Lesson 3 • Drill String Inspection and Maintenance

Teaches visual, dimensional, and non-destructive inspection methods for drill pipe and connections. Prevents costly downhole failures by identifying wear before it becomes critical.

Lesson 4 • Drill String Design and BHA Configuration

Covers bottom-hole assembly design principles for vertical, directional, and horizontal wells. Connects BHA configuration to wellbore trajectory control introduced in Chapter 6.

Lesson 1 • Spudding and Surface Hole Drilling

Covers conductor and surface hole drilling, including bit selection, fluid selection, and rate control. Sets the stage for all subsequent hole sections drilled in the well.

Lesson 2 • Casing and Cementing Operations

Describes casing running procedures, centralizer placement, and primary cementing job execution. Ensures wellbore integrity before drilling the next hole section.

Lesson 3 • Making Connections and Tripping Pipe

Details the step-by-step procedures for making drill pipe connections and tripping in and out of hole. Emphasizes efficiency, safety, and proper torque application at each step.

Lesson 4 • Drilling Parameter Optimization

Applies weight-on-bit, rotary speed, and flow rate adjustments to maximize rate of penetration. Connects parameter selection to bit type and formation characteristics from Chapter 4.

Lesson 1 • Shut-In Procedures

Drills the hard shut-in and soft shut-in sequences for kicks detected while drilling, tripping, and cementing. Correct shut-in captures accurate SIDPP and SICP readings.

Lesson 2 • Formation Pressure and Kick Causes

Explains pore pressure, fracture gradient, and the conditions that allow formation fluids to enter the wellbore. Establishes the pressure fundamentals underlying all well-control actions.

Lesson 3 • Blowout Preventer Systems

Describes annular preventers, ram preventers, choke and kill lines, and accumulator systems. Prepares drillers to operate BOP equipment correctly during a shut-in.

Lesson 4 • Kill Methods and Pressure Management

Applies the driller's method and wait-and-weight method to circulate a kick out safely. Covers kill sheet preparation, choke manipulation, and casing pressure limits.

Lesson 1 • Directional Drilling Tools and Systems

Covers mud motors, rotary steerable systems, and measurement-while-drilling tools used to steer the bit. Connects tool selection to well profile requirements.

Lesson 2 • Survey Calculations and Interpretation

Applies minimum curvature and radius-of-curvature methods to calculate wellbore position. Enables drillers to verify survey data and detect trajectory deviations early.

Lesson 3 • Directional Drilling Concepts

Introduces inclination, azimuth, dogleg severity, and wellbore trajectory planning. Provides the geometric vocabulary needed to interpret survey data and well plans.

Lesson 4 • Driller's Role in Directional Operations

Defines the driller's responsibilities when working alongside a directional driller and MWD engineer. Covers communication, parameter adjustments, and survey acceptance procedures.

Lesson 1 • Mud Pump Operation and Maintenance

Explains duplex and triplex pump operation, liner sizing, and valve and piston maintenance. Proper pump management sustains the hydraulics program from Chapter 3.

Lesson 2 • Rotating Equipment Operation

Addresses top drive and rotary table operation, including torque limits and RPM control. Integrates with drilling parameter optimization from Chapter 5.

Lesson 3 • Power Generation and Distribution

Describes diesel engines, SCR systems, and AC variable-frequency drive power systems on modern rigs. Ensures drillers understand power limitations that affect all rig operations.

Lesson 4 • Hoisting System Operation

Covers drawworks, traveling block, crown block, and deadline anchor operation and load limits. Connects hoisting capacity to drill string weight calculations from Chapter 4.