Chainsaw Operator Course

Lesson 1 • Personal Protective Equipment Selection

Select and inspect PPE appropriate for chainsaw operations, including cut-resistant chaps, helmets, and gloves. Proper PPE use directly reduces severity of common chainsaw injuries.

Lesson 2 • Chainsaw Components and Terminology

Identify all major parts of a chainsaw and understand their functions. This knowledge underpins every maintenance and operational decision made throughout the course.

Lesson 3 • Regulatory and Industry Safety Standards

Understand applicable occupational safety regulations and industry best practices governing chainsaw use. Compliance with these standards is required for legal and professional operation.

Lesson 1 • Maintenance Records and Equipment Logs

Document inspection findings and maintenance actions in equipment logs to track service intervals. Accurate records support accountability and equipment lifecycle management.

Lesson 2 • Engine and Fuel System Maintenance

Perform routine engine maintenance including air filter cleaning, spark plug replacement, and fuel mixing. Proper engine care extends equipment life and ensures reliable starts.

Lesson 3 • Pre-Operational Inspection Procedures

Conduct a structured pre-start inspection covering chain tension, brake function, and fluid levels. Consistent inspection prevents mechanical failures that cause injuries.

Lesson 4 • Chain Sharpening Techniques

Sharpen chainsaw chains using round files, flat files, and depth gauge tools to maintain cutting efficiency. A sharp chain reduces operator fatigue and kickback risk.

Lesson 1 • Starting Procedures: Ground and Drop Start

Execute approved ground-start and drop-start methods while keeping the chain brake engaged. Correct starting technique prevents uncontrolled movement at ignition.

Lesson 2 • Safe Carrying and Transport Procedures

Carry and transport a chainsaw safely between work areas using correct techniques and protective covers. Improper carrying is a leading cause of lacerations during non-cutting activities.

Lesson 3 • Throttle Control and Chain Brake Use

Operate the throttle smoothly and activate the chain brake instinctively during pauses and emergencies. Mastery of these controls is the primary defence against kickback injury.

Lesson 1 • Making Plunge and Boring Cuts

Perform plunge cuts using the lower bar tip to initiate interior cuts in logs and stumps. This advanced basic technique requires precise control to avoid kickback.

Lesson 2 • Cutting Accuracy and Efficiency

Develop consistent cut quality through proper guide bar alignment and smooth feed pressure. Accurate cuts reduce rework, material waste, and unnecessary saw stress.

Lesson 3 • Bucking Downed Timber

Apply correct overbuck and underbuck sequences to cross-cut logs resting on the ground or supports. Proper sequencing prevents bar pinching and maintains operator control.

Lesson 4 • Limbing Downed Trees

Remove branches from felled trees using controlled strokes that keep the saw in the safe operating zone. Limbing sequence and body position prevent saw contact and branch spring-back.

Lesson 1 • Back Cut and Hinge Formation

Execute the back cut at the correct height and depth to create a uniform hinge that guides the fall. Hinge width and thickness control the direction and speed of the falling tree.

Lesson 2 • Notch Cut Techniques

Cut open-face, conventional, and Humboldt notches to control felling direction and hinge formation. Notch type and depth directly determine how accurately the tree falls.

Lesson 3 • Establishing Escape Routes

Plan and clear two escape routes at 45-degree angles opposite the intended felling direction. Pre-planned escape routes are the primary defense against struck-by incidents.

Lesson 4 • Tree Assessment Before Felling

Evaluate tree lean, crown weight distribution, root condition, and surrounding hazards before felling. Thorough assessment determines the safest felling direction and technique.

Lesson 1 • Managing Hung Trees Safely

Identify and safely clear hung trees using approved techniques without standing in the strike zone. Hung trees are among the most dangerous situations a chainsaw operator encounters.

Lesson 2 • Snag and Hazard Tree Removal

Assess and fell dead standing trees and identified hazard trees using conservative, high-margin techniques. Snags present unpredictable structural failure and require maximum caution.

Lesson 3 • Felling on Slopes and Uneven Terrain

Adapt felling technique and escape routes for uphill, downhill, and sidehill tree positions. Slope changes the direction of roll and increases the speed of a falling tree.

Lesson 4 • Felling in Confined and Restricted Spaces

Plan felling operations near structures, power lines, and other trees using sectional and rigging techniques. Confined-space felling requires precise notch alignment and crew coordination.

Lesson 1 • Fatigue Management and Work Rotation

Recognize fatigue indicators and implement work-rest cycles to maintain operator alertness throughout the shift. Fatigue is a primary contributing factor in chainsaw incidents.

Lesson 2 • Waste Management and Site Cleanup

Organize slash disposal, log decking, and site restoration to leave a safe and compliant work area. Proper cleanup prevents trip hazards and supports environmental compliance.

Lesson 3 • Site Assessment and Work Planning

Conduct a systematic site assessment to identify hazards, access routes, and felling sequences before work begins. A written work plan reduces improvised decisions that lead to incidents.

Lesson 4 • Environmental and Weather Considerations

Adjust operations based on wind, rain, ice, and low-light conditions that increase felling risk. Environmental awareness is essential for maintaining safe operational margins.

Lesson 1 • Incident Investigation and Reporting

Document chainsaw incidents using root-cause analysis to identify contributing factors and prevent recurrence. Thorough reporting fulfills regulatory obligations and improves organizational safety.

Lesson 2 • Emergency Communication and Evacuation

Activate emergency response systems, communicate location accurately, and coordinate evacuation from remote sites. Delayed communication is a preventable cause of death in remote incidents.

Lesson 3 • Recognizing and Responding to Chainsaw Lacerations

Apply direct pressure, wound packing, and tourniquet techniques to control severe bleeding from chainsaw cuts. Rapid hemorrhage control is the most critical first-aid skill for chainsaw operators.