Open Cabling Course

Lesson 1 • The Seven Subsystems of Cabling

Introduces each subsystem from entrance facility to work area outlet. Students map subsystems to physical building zones for practical orientation.

Lesson 2 • History and Purpose of Structured Cabling

Traces the evolution from point-to-point wiring to standardised cabling infrastructure. Establishes why structured systems reduce cost and simplify maintenance.

Lesson 3 • Industry Standards and Compliance Basics

Surveys the major international and domestic standards that govern cabling design and installation. Compliance awareness prevents costly rework and liability.

Lesson 1 • Media Selection and Application Mapping

Applies copper and fibre knowledge to real-world application scenarios. Students produce a media selection matrix for a sample building project.

Lesson 2 • Copper Performance Categories

Covers Cat 5e through Cat 8 performance specifications and supported applications. Students select the correct category based on speed, distance, and budget constraints.

Lesson 3 • Copper Cable Types and Construction

Examines UTP, STP, and coaxial cable construction and electrical properties. Understanding construction guides correct selection for bandwidth and interference environments.

Lesson 1 • Copper Connectors and Jacks

Covers RJ-45 modular plugs, keystone jacks, and IDC termination principles. Correct connector selection directly affects channel performance and compliance.

Lesson 2 • Patch Panels and Cross-Connect Hardware

Explains 110-block, patch panel, and fibre distribution panel configurations. Proper hardware selection enables flexible, manageable cross-connect architectures.

Lesson 3 • Fibre Optic Connectors

Surveys LC, SC, ST, and MPO connector types along with polish styles. Connector choice affects insertion loss and compatibility with active equipment.

Lesson 1 • Pathway and Conduit Preparation

Covers conduit types, fill ratios, and pulling preparation before cable installation begins. Proper pathway prep prevents cable damage and code violations.

Lesson 2 • Terminating Copper at Jacks and Panels

Provides step-by-step IDC termination procedures for jacks and patch panels. Consistent termination technique is the single largest factor in copper test results.

Lesson 3 • Cable Pulling and Routing Best Practices

Teaches tension limits, pulling techniques, and bend radius rules for copper cable. Correct pulling prevents pair damage that causes hidden performance failures.

Lesson 1 • Fibre Safety and Handling Procedures

Establishes eye safety, glass fragment disposal, and workspace hygiene for fibre work. Safety compliance protects technicians and prevents contamination-related failures.

Lesson 2 • Fibre Splicing Methods

Compares fusion and mechanical splicing techniques, tools, and loss performance. Splicing knowledge is critical for backbone and outside plant fibre runs.

Lesson 3 • Fibre Installation Quality Verification

Introduces visual fault locator checks and pre-OTDR inspection before formal testing. Early verification catches gross faults before expensive test equipment is deployed.

Lesson 4 • Fibre Connector Termination Methods

Teaches field-polish, pre-polished, and factory-terminated connector installation. Method selection balances cost, loss performance, and field conditions.

Lesson 1 • Troubleshooting Fibre Failures

Applies OTDR and inspection data to isolate high-loss events and reflections. Systematic fibre troubleshooting prevents misdiagnosis and unnecessary connector replacement.

Lesson 2 • Test Reporting and Project Closeout

Covers test report formatting, record retention, and owner deliverable requirements. Complete documentation is required for warranty validation and future maintenance.

Lesson 3 • Troubleshooting Copper Failures

Provides a systematic fault-isolation methodology for common copper test failures. Structured troubleshooting reduces mean time to repair and avoids unnecessary rework.

Lesson 4 • Copper Certification Testing Fundamentals

Explains the key parameters measured during copper channel and permanent link testing. Understanding each parameter enables fast, accurate diagnosis of failures.

Lesson 1 • High-Density Copper Solutions

Covers Cat 6A and Cat 8 deployment strategies for high-density server and switch connections. Alien crosstalk management is the dominant challenge in dense copper environments.

Lesson 2 • Data Centre Cabling Standards Compliance

Reviews data centre-specific cabling standards and their performance requirements. Compliance ensures interoperability with active equipment and supports uptime guarantees.

Lesson 3 • High-Density Fibre Solutions

Examines MPO trunk systems, cassette modules, and pre-terminated fibre assemblies. Pre-terminated systems reduce installation time and improve loss consistency.

Lesson 4 • Power and Cooling Considerations

Introduces power over Ethernet limits and thermal management impacts on cabling. Cabling choices directly affect heat generation and cooling system efficiency.

Lesson 1 • Site Survey and Requirements Gathering

Teaches structured site survey methods to capture physical and performance requirements. Accurate surveys prevent design errors that cause costly field changes.

Lesson 2 • Bill of Materials and Cost Estimation

Develops skills for generating accurate material lists and labour cost estimates. Precise estimation protects project margin and supports competitive bidding.

Lesson 3 • Cabling System Design Principles

Applies subsystem knowledge to produce a compliant, scalable cabling design. Design decisions made here drive all downstream installation and testing activities.

Lesson 4 • Installation Scheduling and Coordination

Covers phased installation planning, subcontractor coordination, and milestone tracking. Effective scheduling minimises disruption to occupied buildings and active networks.