Diesel Heavy Equipment Mechanic Course

Lesson 1 • Shop and Job Site Safety

Teaches hazard identification, personal protective equipment selection, and lockout/tagout procedures. Safety practices introduced here apply throughout every hands-on chapter.

Lesson 2 • Technical Documentation and Standards

Introduces service manuals, parts catalogs, wiring diagrams, and torque specifications. Proficiency with documentation is a prerequisite to accurate diagnosis and repair.

Lesson 3 • Heavy Equipment Industry Overview

Covers the scope of diesel heavy equipment across construction, mining, and agriculture sectors. Establishes industry context that frames all subsequent technical training.

Lesson 1 • Engine Cooling System

Addresses coolant flow, thermostat function, radiator design, and water pump operation. Thermal management knowledge prevents overheating failures covered in later diagnostic chapters.

Lesson 2 • Engine Lubrication System

Details oil pump operation, pressure regulation, filtration, and oil analysis. Lubrication system integrity prevents premature wear across all rotating and sliding components.

Lesson 3 • Engine Block and Rotating Assembly

Covers cylinder block construction, crankshaft, connecting rods, pistons, and bearings. These components form the mechanical core that converts combustion energy into usable power.

Lesson 4 • Valvetrain and Cylinder Head Systems

Examines camshaft operation, valve timing, rocker arms, and cylinder head sealing. Proper valvetrain setup directly affects engine breathing and power output.

Lesson 1 • Common Rail Fuel Systems

Details high-pressure rail operation, pressure regulation, and piezoelectric injector function. Common rail systems dominate modern heavy equipment and require specialized service skills.

Lesson 2 • Electronic Unit Injector Systems

Examines electronically controlled unit injectors, solenoid drivers, and injection timing maps. Electronic control enables precise fueling strategies analyzed in the diagnostics chapter.

Lesson 3 • Mechanical Injection Pump Systems

Explains inline and distributor pump operation, governor function, and timing procedures. Mechanical systems remain common on older heavy equipment fleets.

Lesson 4 • Fuel System Diagnostics and Calibration

Applies diagnostic tools to identify injection timing errors, low power, and excessive smoke. Calibration procedures restore fuel system performance to specification.

Lesson 1 • Exhaust System Components

Covers exhaust manifold design, back pressure measurement, and muffler service. Exhaust system integrity is a prerequisite to understanding aftertreatment systems.

Lesson 2 • Charge Air Cooling Systems

Addresses air-to-air and air-to-liquid intercooler design, pressure testing, and efficiency evaluation. Charge air cooling increases air density and reduces thermal stress on engine components.

Lesson 3 • Air Filtration and Intake Design

Covers dry and wet air filter types, restriction indicators, and intake manifold design. Adequate air filtration protects engine components and sustains combustion quality.

Lesson 4 • Exhaust Aftertreatment Systems

Examines diesel oxidation catalysts, diesel particulate filters, and selective catalytic reduction systems. Aftertreatment service ensures emissions compliance and prevents costly regeneration failures.

Lesson 1 • Sensors, Actuators, and Wiring Harness Repair

Tests pressure, temperature, and position sensors alongside solenoid actuators. Harness repair skills ensure reliable signal transmission throughout the machine.

Lesson 2 • Starting and Charging Systems

Covers starter motor operation, solenoid testing, alternator output, and battery maintenance. Reliable starting and charging are critical for equipment availability in field conditions.

Lesson 3 • Electronic Control Modules and Networks

Explains CAN bus architecture, module communication, and data link diagnostics. Network knowledge is essential for interpreting fault codes and programming control modules.

Lesson 4 • Lighting, Gauges, and Accessory Circuits

Addresses work lighting circuits, instrument cluster signals, and accessory relay logic. Functional gauges and lighting directly affect operator safety and machine monitoring.

Lesson 1 • Hydraulic Valves and Control Circuits

Examines relief valves, directional control valves, flow control valves, and proportional valves. Valve function governs actuator direction, speed, and force in every hydraulic circuit.

Lesson 2 • Hydraulic Principles and Fluid Properties

Establishes Pascal's law, flow, pressure, and hydraulic fluid selection criteria. Theoretical grounding enables accurate interpretation of hydraulic circuit behavior.

Lesson 3 • Hydraulic Cylinders and Motors

Details cylinder seal replacement, rod inspection, and hydraulic motor efficiency testing. Actuator condition determines the precision and force of implement and drive functions.

Lesson 4 • Hydraulic Pumps

Covers gear, vane, and piston pump construction, displacement control, and wear diagnosis. Pump output directly determines the force and speed of all hydraulic actuators.

Lesson 1 • Power Shift and Automatic Transmissions

Covers clutch pack operation, planetary gear sets, and electronic shift control. Transmission service requires integration of hydraulic and electronic skills from prior chapters.

Lesson 2 • Steering and Brake Systems

Examines hydrostatic steering, differential steering, and wet disc brake operation. Steering and brake integrity are critical safety systems on all heavy equipment.

Lesson 3 • Crawler Undercarriage Components

Covers track chain, sprocket, idler, roller, and track frame inspection and adjustment. Undercarriage wear accounts for a significant portion of crawler equipment operating costs.

Lesson 4 • Drive Axles and Final Drives

Addresses differential operation, axle shaft service, and planetary final drive maintenance. Final drive condition directly affects tractive effort and machine manoeuvrability.

Lesson 1 • Systematic Diagnostic Methodology

Establishes a structured fault isolation process using symptom analysis, data collection, and verification. A repeatable diagnostic method reduces repair time and prevents misdiagnosis.

Lesson 2 • Telematics and Remote Monitoring

Introduces GPS-based telematics, fault alert systems, and remote diagnostic capabilities. Telematics data enables proactive maintenance decisions and reduces unplanned downtime.

Lesson 3 • Oil and Fluid Analysis Programs

Explains sampling procedures, laboratory report interpretation, and corrective action planning. Fluid analysis detects internal wear and contamination before catastrophic failure occurs.

Lesson 4 • Electronic Service Tool Operation

Covers scan tool navigation, live data interpretation, active tests, and software updates. Electronic service tools are the primary interface for diagnosing modern heavy equipment.