Mep Engineer Course

Lesson 1 • Engineering Drawing and Documentation

Covers reading and interpreting MEP drawings, symbols, and schedules. Provides the document literacy needed for all subsequent design and coordination tasks.

Lesson 2 • MEP Disciplines and Scope

Defines mechanical, electrical, and plumbing engineering roles within construction projects. Connects discipline boundaries to collaborative design workflows.

Lesson 3 • Building Systems Integration Overview

Examines how HVAC, electrical, and plumbing systems share space and interact structurally. Builds awareness of spatial conflicts and coordination priorities.

Lesson 4 • Codes, Standards, and Regulations

Introduces regulatory frameworks governing MEP design, including safety and energy standards. Establishes compliance as a non-negotiable design constraint.

Lesson 1 • Ventilation and Indoor Air Quality

Applies ventilation rate standards to ensure adequate fresh air and pollutant dilution. Links ventilation design to occupant health and regulatory compliance.

Lesson 2 • Ductwork Design and Air Distribution

Covers duct sizing methods, pressure loss calculations, and diffuser placement for balanced airflow. Proper distribution ensures comfort and energy efficiency.

Lesson 3 • Hydronic Heating and Cooling Systems

Designs chilled water and hot water piping systems including pump sizing and pipe layout. Hydronic systems serve large commercial and institutional buildings.

Lesson 4 • Psychrometrics and Thermal Comfort

Explains air properties, moisture content, and human comfort parameters. Provides the thermodynamic basis for all HVAC sizing and control decisions.

Lesson 5 • Heating and Cooling Load Calculations

Applies heat transfer principles to calculate building thermal loads using industry-standard methods. Accurate loads drive equipment sizing and energy performance.

Lesson 1 • Domestic Water Supply Systems

Covers cold and hot water distribution design, pressure requirements, and pipe sizing methods. Establishes the supply framework for all downstream plumbing components.

Lesson 2 • Fire Suppression and Specialty Systems

Introduces wet-pipe, dry-pipe, and clean-agent suppression systems and their design parameters. Specialty systems include medical gas and laboratory plumbing.

Lesson 3 • Sanitary Drainage and Venting

Designs gravity drainage systems and vent stacks to maintain trap seals and prevent sewer gas entry. Correct slope and venting are critical for system function.

Lesson 4 • Stormwater and Roof Drainage

Sizes roof drains, leaders, and site drainage systems based on rainfall intensity data. Connects stormwater management to site and structural coordination.

Lesson 1 • Panelboard and Circuit Design

Designs branch circuit panelboards, load schedules, and circuit breaker coordination. Balanced loading and proper protection are key outcomes.

Lesson 2 • Utility Service and Metering

Covers utility service entrance design, metering arrangements, and coordination with utility providers. Service sizing sets the capacity ceiling for the entire building.

Lesson 3 • Transformers and Switchgear

Explains transformer types, ratings, and placement alongside switchgear and switchboard design. These components form the backbone of building power distribution.

Lesson 4 • Grounding and Bonding Systems

Applies grounding and bonding requirements to ensure personnel safety and equipment protection. Correct grounding is mandatory for code compliance.

Lesson 1 • Standby and Backup Power Systems

Covers generator sizing, automatic transfer switches, and uninterruptible power supply design. Backup power ensures critical loads remain energized during outages.

Lesson 2 • Lighting Design Principles

Applies photometric concepts to design interior and exterior lighting for visual comfort and energy compliance. Illuminance targets vary by space type and task.

Lesson 3 • Lighting Controls and Energy Compliance

Designs occupancy sensing, daylight harvesting, and dimming controls to meet energy standards. Controls reduce energy use while maintaining occupant comfort.

Lesson 4 • Low-Voltage and Specialty Systems

Introduces fire alarm, data, security, and audiovisual systems within the MEP scope. Coordination with other trades is essential for pathway and device placement.

Lesson 1 • Coordination Drawings and Shop Drawings

Produces composite coordination drawings and reviews contractor shop drawings for compliance. These documents bridge design intent and field installation.

Lesson 2 • MEP Model Deliverables and Standards

Establishes model quality standards, deliverable formats, and handover requirements for MEP BIM projects. Consistent standards enable downstream use by contractors and owners.

Lesson 3 • BIM Fundamentals for MEP Engineers

Introduces BIM concepts, model authoring environments, and MEP-specific modeling workflows. BIM literacy is prerequisite for all coordination tasks in this chapter.

Lesson 4 • Clash Detection and Resolution

Uses federated models and clash detection software to identify and resolve hard and soft clashes. Systematic resolution prevents costly field conflicts.

Lesson 1 • Passive Design Strategies

Integrates building orientation, shading, natural ventilation, and thermal mass to reduce MEP loads. Passive strategies lower system capacity requirements and operating costs.

Lesson 2 • Renewable Energy Integration

Designs photovoltaic, solar thermal, and geothermal systems as MEP energy sources. Renewable integration requires coordination with structural and electrical systems.

Lesson 3 • High-Efficiency MEP Equipment

Evaluates high-efficiency chillers, heat pumps, variable-speed drives, and LED lighting for energy savings. Equipment efficiency ratings directly affect energy model outcomes.

Lesson 4 • Building Energy Modeling Fundamentals

Introduces whole-building energy simulation tools, input parameters, and output interpretation. Energy models quantify system performance and guide design decisions.

Lesson 1 • Design Phase Deliverables and Milestones

Defines schematic, design development, and construction document deliverables for MEP disciplines. Milestone content requirements align with owner and contractor expectations.

Lesson 2 • Bidding, Procurement, and Submittals

Manages the MEP bidding process, contractor selection criteria, and submittal review workflows. Thorough submittal review ensures installed equipment matches design intent.

Lesson 3 • Commissioning and Project Closeout

Leads MEP commissioning activities, punch list resolution, and owner training for building systems. Closeout documentation ensures long-term operability and warranty compliance.

Lesson 4 • Cost Estimating and Value Engineering

Applies MEP cost estimating methods and value engineering techniques to optimize project budgets. Cost awareness shapes system selection and specification decisions.