PTC Creo training

Lesson 1 • Mouse Controls and View Manipulation

Teaches pan, zoom, rotate, and view orientation commands. Smooth view control accelerates every modelling task in later sections.

Lesson 2 • File Management and Working Directory

Explains Creo file types, working directory setup, and save strategies. Proper file hygiene prevents data loss throughout the course.

Lesson 3 • Customising the Creo Environment

Covers config.pro options, mapkeys, and display settings. A tailored environment improves productivity in all design sessions.

Lesson 4 • Navigating the Creo User Interface

Introduces ribbons, model tree, graphics area, and status bar. Efficient navigation is prerequisite to all hands-on exercises.

Lesson 1 • Entering and Configuring Sketcher

Explains how to enter Sketcher, select sketch planes, and set references. Correct setup prevents constraint errors in downstream features.

Lesson 2 • Applying Geometric Constraints

Covers horizontal, vertical, tangent, symmetric, and coincident constraints. Geometric constraints define design intent without dimensions.

Lesson 3 • Sketcher Diagnostic and Editing Tools

Uses shade, highlight, and diagnostic tools to verify sketch completeness. Editing skills enable rapid iteration during feature creation.

Lesson 4 • Drawing Basic Geometry

Teaches lines, arcs, circles, rectangles, and splines using Sketcher tools. These primitives form the basis of all part features.

Lesson 1 • Datum Axes and Points

Covers axis creation through cylinders, edges, and intersections, plus point placement. Axes and points anchor features and assembly constraints.

Lesson 2 • Using Datums for Feature Placement

Demonstrates selecting datums as sketch planes, mirrors, and pattern references. Proper datum use is the key to robust parametric models.

Lesson 3 • Datum Curves and Coordinate Systems

Introduces sketched, projected, and wrap datum curves plus coordinate system creation. These references support advanced sweep and surface features.

Lesson 1 • Sweep Feature Creation

Explains trajectory and cross-section relationships for swept protrusions and cuts. Sweeps model pipes, channels, and complex extrusions.

Lesson 2 • Feature Order and Model Tree Management

Covers reordering, suppressing, and resuming features in the model tree. Tree management maintains model integrity as complexity grows.

Lesson 3 • Revolve Feature Creation

Covers revolving sketches around an axis to create rotational solids and cuts. Revolve is essential for shafts, discs, and symmetric parts.

Lesson 4 • Extrude Feature Creation

Teaches blind, symmetric, and through-all extrusions for both protrusions and cuts. Extrude is the most frequently used solid feature in Creo.

Lesson 1 • Round and Chamfer Features

Teaches constant, variable, and full rounds plus chamfer types and propagation. Edge treatments are critical for aesthetics and stress reduction.

Lesson 2 • Shell Feature and Wall Thickness

Explains shell feature setup, excluded surfaces, and non-uniform thickness. Shell converts solid parts into thin-walled plastic or cast components.

Lesson 3 • Rib and Draft Features

Covers profile and trajectory ribs plus draft angle application for moulded parts. Ribs and drafts are essential for injection-moulded component design.

Lesson 4 • Hole Feature Types and Placement

Covers simple, sketched, standard, and counterbore holes with placement references. Hole features carry semantic data used in drawings and BOMs.

Lesson 1 • Assembly Fundamentals and Strategies

Explains bottom-up, top-down, and mixed assembly strategies with file structure. Strategy selection determines design flexibility and data reuse.

Lesson 2 • Interference and Clearance Analysis

Uses global interference and clearance checks to validate assembly fit. Analysis results guide design corrections before physical prototyping.

Lesson 3 • Placing and Constraining Components

Covers mate, align, insert, and coincident constraints to fully position parts. Correct constraints reflect real-world physical relationships between parts.

Lesson 4 • Exploded Views and Bill of Materials

Creates exploded views with offset lines and generates a structured BOM. These outputs are required for assembly documentation and procurement.

Lesson 1 • Notes, Tables, and Drawing Completion

Adds general notes, surface finish symbols, weld symbols, and BOM tables. Complete annotation packages drawings for release to manufacturing.

Lesson 2 • Creating and Arranging Views

Teaches general, projection, auxiliary, section, and detail views. Proper view selection communicates part geometry without ambiguity.

Lesson 3 • Drawing Setup and Format

Covers drawing templates, formats, title blocks, and drawing options files. Consistent setup ensures drawings meet company and industry standards.

Lesson 4 • Geometric Dimensioning and Tolerancing

Applies GD&T symbols, datum feature symbols, and feature control frames. GD&T precisely communicates form, orientation, and location requirements.

Lesson 1 • Basic Surface Feature Creation

Covers extruded, revolved, swept, and blended surfaces using Creo surface tools. These features mirror solid counterparts but produce open geometry.

Lesson 2 • Surface Modelling Concepts

Distinguishes solid and surface modelling paradigms and explains quilt structure. Understanding quilts is essential before creating or editing surfaces.

Lesson 3 • Solidifying and Thickening Surfaces

Converts closed quilts to solids and open quilts to thin solids using solidify and thicken. This step integrates surface work into the part model.

Lesson 4 • Surface Editing Operations

Applies trim, merge, extend, offset, and copy operations to refine quilts. Editing operations transform raw surfaces into precise engineering geometry.