Electrical Training for Designated Tasks

Lesson 1 • Lockout and Tagout Procedures

Teaches energy isolation methods to prevent accidental energization during maintenance. Mastery of LOTO is a prerequisite for all equipment-level tasks.

Lesson 2 • Regulatory Compliance Basics

Introduces workplace electrical safety regulations and employer obligations. Compliance awareness shapes decision-making throughout all designated task activities.

Lesson 3 • Personal Protective Equipment Selection

Identifies PPE categories rated for electrical work and correct selection criteria. Proper PPE use underpins every designated task performed in this course.

Lesson 1 • Inductance, Capacitance, and Impedance

Introduces reactive components and their effect on AC circuit behavior. Impedance concepts are essential for motor and transformer work in advanced chapters.

Lesson 2 • Series and Parallel Circuits

Analyzes current paths, voltage drops, and resistance in series and parallel configurations. These circuit types appear in every electrical installation covered later.

Lesson 3 • Voltage, Current, and Resistance

Defines the three fundamental electrical quantities and their interrelationships. Understanding these quantities is required before analyzing any circuit.

Lesson 4 • Power and Energy Calculations

Applies power formulas to determine load requirements and energy consumption. Accurate power calculations support safe equipment sizing in later chapters.

Lesson 1 • Insulation Resistance Testing

Explains megohmmeter operation to assess insulation integrity of cables and motors. Insulation testing prevents failures and is required before energizing repaired equipment.

Lesson 2 • Multimeter Operation and Safety

Covers multimeter functions, safety ratings, and correct probe technique. Safe meter use is foundational to all diagnostic tasks in this course.

Lesson 3 • Clamp Meter and Current Measurement

Teaches non-contact current measurement using clamp meters on AC and DC circuits. Clamp meters are the primary tool for load verification in designated tasks.

Lesson 1 • Cable Wiring Methods

Covers installation of armored, metal-clad, and non-metallic sheathed cable systems. Cable methods are common in commercial and light industrial designated tasks.

Lesson 2 • Splicing and Termination Techniques

Demonstrates proper conductor splicing, connector selection, and terminal torque requirements. Reliable terminations are critical to system safety and longevity.

Lesson 3 • Conductor Sizing and Ampacity

Applies ampacity tables and correction factors to size conductors for specific loads. Proper sizing is mandatory before any wiring installation task.

Lesson 4 • Conduit and Raceway Systems

Teaches installation of rigid, flexible, and non-metallic conduit systems. Raceway selection and installation protect conductors in all designated task environments.

Lesson 1 • Overcurrent Device Sizing and Selection

Applies sizing rules for branch circuits, feeders, and motor circuits. Correct sizing prevents nuisance tripping and ensures fault clearing under all conditions.

Lesson 2 • Fuses and Circuit Breaker Fundamentals

Covers fuse types, circuit breaker operation, and interrupting ratings. Selecting the correct overcurrent device is the first step in any circuit protection task.

Lesson 3 • System Grounding Principles

Explains grounded and grounding conductors, neutral-to-ground bonding, and ground electrode systems. Proper grounding limits voltage rise during faults and lightning events.

Lesson 4 • Equipment Grounding and Bonding

Covers equipment grounding conductor installation and bonding of metallic enclosures. Effective bonding creates a low-impedance fault-return path to clear overcurrent devices.

Lesson 1 • Panelboard Components and Layout

Identifies bus bars, breaker positions, neutral bars, and enclosure components. Component familiarity is required before any work inside distribution equipment.

Lesson 2 • Circuit Directory and Labeling

Covers accurate circuit identification, directory completion, and panel schedule documentation. Proper labeling is a regulatory requirement and a safety necessity.

Lesson 3 • Circuit Breaker Installation and Replacement

Demonstrates safe breaker installation, torque requirements, and handle-tie applications. Correct installation ensures reliable overcurrent protection for each circuit.

Lesson 4 • Switchgear and Motor Control Centers

Introduces switchgear construction, draw-out breaker operation, and motor control center (MCC) bucket handling. These skills apply to industrial designated task environments.

Lesson 1 • Motor Circuit Components and Wiring

Identifies disconnects, contactors, overload relays, and control transformers in motor circuits. Correct component wiring is required before energizing any motor installation.

Lesson 2 • Motor Starter Installation and Testing

Demonstrates full-voltage and reduced-voltage starter wiring, testing, and overload setting. Proper starter setup protects motors and ensures reliable starting performance.

Lesson 3 • Motor Troubleshooting Techniques

Applies systematic diagnostic methods to identify motor, starter, and control circuit faults. Efficient troubleshooting minimizes downtime in industrial designated task settings.

Lesson 4 • Variable-Frequency Drive Fundamentals

Covers VFD operating principles, parameter programming, and input/output wiring. VFDs are standard in modern motor control and require specific installation practices.

Lesson 1 • Quality Verification and Commissioning

Applies inspection checklists and functional tests to verify completed electrical installations. Commissioning confirms that all work meets design specifications before handover.

Lesson 2 • Task Planning and Work Permits

Covers job hazard analysis, work permit completion, and task sequencing before starting work. Thorough planning prevents incidents and ensures regulatory compliance.

Lesson 3 • Reading and Interpreting Electrical Drawings

Develops proficiency in reading schematic, wiring, and one-line diagrams for task execution. Drawing interpretation is essential for accurate installation and troubleshooting.

Lesson 4 • Incident Response and Near-Miss Reporting

Prepares workers to respond to electrical incidents and report near-misses effectively. Prompt reporting drives corrective actions that prevent future injuries.