Handyman Training Course

Lesson 1 • Regulatory and Compliance Basics

Introduces building codes, safety regulations, and permit concepts relevant to minor repairs. Ensures students recognize when compliance checks are required.

Lesson 2 • Workplace Safety and Hazard Awareness

Covers personal protective equipment, hazard identification, and safe work practices. Directly supports safe execution of all subsequent repair tasks.

Lesson 3 • Essential Tools and Their Uses

Introduces hand tools, power tools, and measuring instruments used across repair tasks. Students match tools to specific repair categories covered later.

Lesson 4 • Defining the Repair Specialist Role

Clarifies the scope of minor repairs versus major renovation work. Establishes professional expectations and typical job contexts for a repair specialist.

Lesson 1 • Finishing Materials and Coatings

Covers paints, primers, stains, and surface coatings used to complete repairs. Students match coating type to substrate and environmental exposure.

Lesson 2 • Fasteners, Adhesives, and Sealants

Teaches selection of screws, nails, anchors, adhesives, and sealants for varied substrates. Correct fastener choice prevents joint failure and callbacks.

Lesson 3 • Material Estimation and Waste Reduction

Teaches quantity takeoff methods and waste-factor calculations for repair projects. Accurate estimation reduces cost overruns and unnecessary material disposal.

Lesson 4 • Masonry, Concrete, and Mortar

Introduces brick, block, concrete, and mortar types relevant to patching and repair. Students distinguish material properties to choose correct repair compounds.

Lesson 1 • Masonry Crack and Joint Repair

Covers tuckpointing, crack injection, and surface sealing for masonry substrates. Students restore structural integrity and weatherproofing to masonry assemblies.

Lesson 2 • Sanding, Priming, and Surface Finishing

Teaches progressive sanding grits, primer application, and final surface preparation. Proper finishing ensures paint adhesion and a seamless visual result.

Lesson 3 • Assessing Damage Before Repair

Teaches systematic inspection of cracks, holes, and delamination before selecting a repair method. Accurate diagnosis prevents mismatched repairs and recurring failures.

Lesson 4 • Drywall Patching Techniques

Covers small hole fills, California patches, and backing-board methods for drywall. Students select the correct technique based on hole size and wall type.

Lesson 1 • Cabinet and Drawer Repairs

Teaches hinge adjustment, drawer slide replacement, and door front realignment. Students restore cabinet function and appearance with minimal material replacement.

Lesson 2 • Hardwood and Laminate Floor Repairs

Covers squeaky floor fixes, plank replacement, and laminate chip repair. Students match existing floor finish and pattern for invisible repairs.

Lesson 3 • Window Repair and Weatherstripping

Teaches sash repair, glazing compound replacement, and weatherstrip installation. Students restore window operation and energy performance without full replacement.

Lesson 4 • Trim, Molding, and Baseboard Repairs

Covers scribing, coping, splicing, and reattaching loose trim and molding. Students achieve tight, paint-ready joints on interior trim profiles.

Lesson 1 • Pipe Leak Repair Techniques

Teaches compression coupling, push-fit fitting, and pipe patch methods for minor leaks. Students select the correct repair method based on pipe material and access.

Lesson 2 • Plumbing System Fundamentals

Introduces supply, drain-waste-vent, and fixture connection concepts. Students understand water flow and pressure principles before attempting any repair.

Lesson 3 • Toilet Repair and Adjustment

Teaches flapper replacement, fill valve adjustment, and wax ring reseating. Students resolve running, rocking, and leaking toilet issues safely.

Lesson 4 • Faucet and Valve Repair

Covers cartridge, ball, and compression faucet disassembly and repair. Students stop drips and restore smooth operation using correct replacement parts.

Lesson 1 • Circuit Breaker and Panel Basics

Introduces breaker identification, tripped breaker reset, and single-breaker replacement. Students recognize panel limitations and escalate complex issues appropriately.

Lesson 2 • Low-Voltage and Doorbell Repairs

Covers doorbell transformer testing, button replacement, and low-voltage wire splicing. Students repair low-voltage systems with minimal shock risk.

Lesson 3 • Outlet and Switch Replacement

Covers GFCI, standard, and USB outlet replacement plus single-pole and three-way switch swaps. Students wire devices correctly and verify safe operation before closing boxes.

Lesson 4 • Electrical Safety and Lockout Procedures

Establishes non-negotiable safety rules, lockout/tagout steps, and testing protocols. All subsequent electrical tasks depend on mastery of these safety fundamentals.

Lesson 1 • Gutter and Downspout Maintenance

Covers gutter cleaning, slope correction, joint sealing, and downspout extension. Proper drainage management prevents foundation and fascia water damage.

Lesson 2 • Siding Repair and Replacement

Covers vinyl, wood, and fiber-cement siding panel removal and replacement. Students match existing profiles and restore weather resistance at repair seams.

Lesson 3 • Exterior Paint and Wood Preservation

Teaches scraping, priming, and painting exterior wood surfaces for long-term protection. Students apply preservatives and coatings that resist UV, moisture, and rot.

Lesson 4 • Roof Patching and Flashing Repair

Introduces shingle replacement, flat roof patching, and flashing resealing techniques. Students address minor roof leaks safely without full roof replacement.

Lesson 1 • Material and Tool Procurement

Covers supplier selection, material ordering, and tool staging for repair jobs. Efficient procurement eliminates delays and reduces unnecessary site visits.

Lesson 2 • Client Communication and Handover

Teaches progress updates, scope change communication, and final walkthrough procedures. Clear communication builds client trust and reduces post-job disputes.

Lesson 3 • Quality Inspection Techniques

Introduces self-inspection checklists, defect identification, and corrective action steps. Students verify their own work meets professional standards before client handover.

Lesson 4 • Invoicing and Job Documentation

Covers time tracking, material cost recording, and invoice preparation for repair jobs. Accurate documentation supports payment, warranty claims, and future reference.