Vehicle Modification Course

Lesson 1 • Vehicle Anatomy and Systems

Introduces major vehicle systems relevant to customization work. Provides the mechanical vocabulary needed to communicate with clients and technicians.

Lesson 2 • Regulatory and Compliance Basics

Outlines safety, emissions, and roadworthiness standards that govern modifications. Compliance knowledge prevents costly rework and legal liability for clients.

Lesson 3 • Industry Overview and Career Paths

Maps the customization market segments and specialist roles. Establishes context for all subsequent technical and business skills covered in the course.

Lesson 1 • Surface Preparation Principles

Teaches cleaning, degreasing, and abrasion methods that ensure coating adhesion. Proper prep is the single greatest factor in long-term finish quality.

Lesson 2 • Adhesives, Sealants, and Fasteners

Reviews bonding agents, seam sealers, and mechanical fasteners for mixed-material assemblies. Correct product selection ensures durability and prevents galvanic corrosion.

Lesson 3 • Metals Used in Vehicle Builds

Examines steel, aluminium, and specialty alloys in terms of properties and workability. Material selection directly affects structural integrity and fabrication method choice.

Lesson 1 • Body Filler and Blocking

Teaches mixing, application, and block-sanding of polyester and lightweight fillers. Correct technique produces straight, guide-coat-verified surfaces ready for primer.

Lesson 2 • Aftermarket Body Kit Installation

Covers fitting, trimming, and bonding aftermarket bumpers, splitters, and side skirts. Proper gap and flush alignment ensures a factory-quality appearance.

Lesson 3 • Roof and Structural Modifications

Addresses chop tops, sunroof deletions, and structural reinforcement after body cuts. Maintaining chassis rigidity is critical when removing structural material.

Lesson 4 • Panel Removal and Disassembly

Covers systematic disassembly sequences to avoid damage to clips, wiring, and trim. Organised disassembly reduces reassembly time and prevents part loss.

Lesson 1 • Custom Paint Effects

Introduces candy coats, fades, and two-tone layouts using masking and blending techniques. These effects differentiate custom builds and command premium pricing.

Lesson 2 • Spray Gun Setup and Technique

Teaches fluid tip selection, air pressure settings, and spray pattern adjustment for HVLP and LVLP guns. Consistent technique eliminates runs, sags, and dry spray.

Lesson 3 • Paint Correction and Polishing

Teaches compounding, polishing, and finishing to remove defects and maximise gloss. Correction skills are essential after paint application and for pre-delivery detailing.

Lesson 4 • Primer Systems and Application

Covers epoxy, urethane, and high-build primers and their roles in the coating stack. Correct primer selection seals bare metal and provides a stable base for colour.

Lesson 1 • Flat and Simple Curve Wrapping

Teaches squeegee technique, film tension management, and heat application on flat panels. Mastery of flat surfaces builds the foundation for complex geometry work.

Lesson 2 • Vinyl Film Types and Properties

Compares cast vs. calendered films, finishes, and adhesive technologies for different applications. Material knowledge guides correct product selection for durability and conformability.

Lesson 3 • Surface Prep and Environment Control

Covers cleaning protocols, temperature requirements, and contamination prevention before wrapping. Proper prep is the primary factor in long-term wrap adhesion.

Lesson 4 • Paint Protection Film Application

Covers PPF cutting software, wet application, and squeegee technique for self-healing films. PPF installation protects high-impact areas and adds service revenue.

Lesson 1 • Lowering and Lift Systems

Covers coilovers, lowering springs, air suspension, and lift kits for different build goals. Each system has distinct ride quality, adjustability, and compliance implications.

Lesson 2 • Wheel and Tyre Selection

Teaches offset, backspacing, bolt pattern, and load rating calculations for fitment. Correct wheel and tyre sizing prevents rubbing and maintains safe load capacity.

Lesson 3 • Alignment and Corner Weighting

Covers four-wheel alignment procedures and corner weight balancing for performance builds. Proper alignment maximises tyre life and achieves predictable handling.

Lesson 4 • Fender Modification for Fitment

Addresses rolling, pulling, and flaring fenders to clear wider wheel and tyre combinations. Fender work must preserve corrosion protection and structural integrity.

Lesson 1 • Custom Seat Fabrication

Addresses bucket seat modification, custom foam builds, and race seat integration with harness mounts. Seat work must comply with occupant restraint safety requirements.

Lesson 2 • Upholstery Fundamentals

Teaches pattern making, cutting, sewing, and stapling techniques for seats and door panels. Foundational upholstery skills apply to every interior surface in the vehicle.

Lesson 3 • Dashboard and Console Customisation

Teaches dash wrapping, gauge pod fabrication, and centre console modification for a cohesive cockpit. Custom dash work requires careful airbag and wiring management.

Lesson 4 • Door Panels and Headliners

Covers substrate fabrication, wrapped panels, and custom headliner installation with lighting integration. Panel work ties the interior theme together and conceals wiring.

Lesson 1 • Custom Lighting Systems

Covers LED strip installation, underglow, accent lighting, and controller programming for custom effects. Lighting must meet visibility and roadworthiness standards where applicable.

Lesson 2 • Relay and Switch Panel Installation

Teaches relay logic, fused distribution blocks, and custom switch panel wiring for accessory loads. Relays protect switches and allow high-current accessories to operate reliably.

Lesson 3 • Wiring Harness Design and Routing

Covers wire gauge selection, loom routing, connector choice, and harness documentation. A well-designed harness prevents shorts, voltage drop, and future diagnostic headaches.

Lesson 4 • Automotive Electrical Fundamentals

Reviews voltage, current, resistance, and circuit types as applied to 12V vehicle systems. Electrical theory underpins every wiring decision made in a custom build.