Leather Crafting Course

Lesson 1 • Understanding Leather Types and Grades

Covers full-grain, top-grain, genuine, and bonded leather distinctions. Establishes material literacy essential for all subsequent project decisions.

Lesson 2 • Measuring and Marking Leather

Teaches accurate measurement with rulers, wing dividers, and silver pens. Precision marking directly affects cut quality and finished dimensions.

Lesson 3 • Workspace Setup and Safety

Defines ergonomic bench layout, ventilation needs, and chemical handling rules. Safe habits established here prevent injury throughout the course.

Lesson 1 • Skiving for Thinning and Joining

Introduces flat, edge, and channel skiving to reduce bulk at seams and folds. Skiving quality determines how cleanly layers bond and fold.

Lesson 2 • Cutting Straps and Strips

Teaches strap-cutting with a strap cutter and draw gauge for uniform width. Consistent strips are critical for handles, belts, and binding.

Lesson 3 • Pattern Making and Nesting

Covers drafting paper patterns, adding seam allowances, and nesting pieces to minimise waste. Efficient nesting reduces material cost on every project.

Lesson 1 • Burnishing Raw Edges

Covers tokonole, beeswax, and gum tragacanth application with wood and canvas burnishers. Burnished edges seal fibres and create a polished appearance.

Lesson 2 • Dyeing and Painting Leather

Covers alcohol dyes, acrylic paints, and antiquing techniques applied before assembly. Colour decisions made at this stage affect all finishing steps.

Lesson 3 • Surface Cleaning and Conditioning

Introduces deglazing, cleaning, and conditioning leather before dyeing or assembly. Proper prep ensures adhesives and dyes bond uniformly.

Lesson 1 • Surface Preparation for Bonding

Covers roughing flesh sides, applying deglazer, and ensuring dry surfaces before gluing. Proper prep is the single largest factor in bond strength.

Lesson 2 • Troubleshooting Bond Failures

Addresses delamination causes, re-bonding procedures, and preventing glue bleed-through. Diagnosing failures early saves materials and project time.

Lesson 3 • Types of Leather Adhesives

Compares contact cement, rubber cement, and water-based glues by strength and flexibility. Adhesive choice affects both bond durability and workability.

Lesson 1 • Pricking and Spacing Stitch Holes

Covers pricking iron selection, consistent spacing, and corner hole placement. Even hole spacing is the foundation of a uniform stitch line.

Lesson 2 • Stitch Quality Inspection

Covers visual and tactile checks for even tension, consistent angle, and secure ends. Inspection skills allow students to self-correct before finishing.

Lesson 3 • Saddle Stitch Execution

Teaches the two-needle saddle stitch sequence, tension control, and locking the final stitch. Saddle stitch is stronger than machine stitch and self-repairs if cut.

Lesson 4 • Thread Selection and Waxing

Introduces linen, polyester, and nylon thread weights matched to leather thickness. Waxing thread reduces friction and prevents tangling during stitching.

Lesson 1 • Zipper Installation in Leather Goods

Teaches gluing, stitching, and finishing metal and nylon zippers in pouches and bags. Zipper tape must be fully bonded before stitching to prevent puckering.

Lesson 2 • Snap Fasteners and Magnetic Closures

Teaches line-20 and line-24 snap installation and magnetic snap placement for flap closures. Alignment accuracy prevents misaligned closures on finished goods.

Lesson 3 • Buckles, D-Rings, and Loops

Covers bar-tack stitching, folded keeper loops, and D-ring attachment for straps and bags. Hardware must be centred and stitched to resist lateral pull.

Lesson 1 • Tote Bag with Handles

Builds a structured tote with stitched handles, reinforced attachment points, and a flat base. Handle reinforcement and load distribution are the key technical challenges.

Lesson 2 • Zipper Pouch Construction

Covers cutting, zipper installation, gusset attachment, and edge finishing for a zipper pouch. Students practise curved seams and zipper technique simultaneously.

Lesson 3 • Structured Bag with Lining

Introduces interfacing, fabric lining attachment, and interior pocket construction for a structured bag. Lining adds durability and a professional interior finish.

Lesson 4 • Project Review and Self-Assessment

Students evaluate finished goods against quality benchmarks for stitching, edges, hardware, and symmetry. Self-assessment builds the critical eye needed for professional output.

Lesson 1 • Embossing and Debossing

Teaches heat embossing, cold press debossing, and logo plate use for branded impressions. Consistent pressure and temperature produce sharp, repeatable impressions.

Lesson 2 • Welt and Turned-Edge Construction

Introduces welt seams and turned-edge technique for structured bags and wallets. These methods hide raw edges and add structural rigidity to finished goods.

Lesson 3 • Professional Surface Finishing

Covers resolene, carnauba cream, and matte finisher application for protection and sheen. Final finish determines the product's durability and visual appeal.

Lesson 4 • Leather Carving and Stamping

Covers casing leather, swivel knife use, and beveler stamping for decorative relief carving. Carving requires precise moisture control and consistent tool pressure.